Onicon F-3200 Series Manual de usuario descargar pdf (Pagina 32)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax (727) 442-5699 • [email protected]

F-3200 Flow Meter Manual 05/14 - 0671-12 / 18325 Page 32

4.2 HELPFUL HINTS FOR START-UP AND COMMISSIONING

A step-by-step procedure and companion worksheet are located on the next two pages. Please

read all installation instructions and these helpfull hints carefully before proceeding with

installation, start-up and commissioning.

1. ONICON ow meters are individually calibrated for a particular application. Be sure to verify the pipe

size and location.

2. The electronic sensing system will not work in air. The pipe must be full for proper operation.

3. When measuring analog output signals, remember that currents (mA) must be measured in series, while

voltages are measured in parallel. If the 4-20 mA signal is already connected to a control system, you

must break the connection and measure the signal in series.

4. When measuring frequency outputs in hertz, take your multimeter out of “autorange mode” and

manually set range for a voltage level above 15 VDC. This will prevent false readings when signal is not

present.

5. Never connect power to analog or frequency output signal wires. ONICON F-3200 Flow Meters are not

“loop powered” devices.

4.3 START-UP AND COMMISSIONING

Please read the entire procedure carefully before proceeding. Wiring instructions are located

on pages 21 - 24 of this manual. A worksheet for checking off the following steps and recording

measured values is located on the next page.

1. Conrm ow meter

location and adequate straight

pipe run to achieve desired

results.

Is the meter located in the correct location as required by the plans?

Compare actual straight pipe upstream and downstream of the meter location to recommend-

ed distances identied in this manual.

2. Conrm control system

programming.

Conrm that the control system input point is properly congured for the analog range

(or scale factor) identied on the calibration certicate.

3. Conrm connection to correct

ONICON display or Btu meter

(if ordered).

Conrm that the ow meter serial number matches the ONICON display or Btu meter

serial number (when ordered together).

4. Verify wiring before

connecting power.

Prior to connecting the power, verify that the wiring is correct as shown in this manual and/or

the additional wiring diagram provided with ONICON display or Btu meter. If in doubt, call

factory for assistance before proceeding further.

5. Verify that the input voltage

available to power the meter

is appropriate for the meter

version. (Check label inside

transmitter enclosure LV=Low

voltage, HV=High voltage.

Low voltage: 18 - 63 VDC or 15 - 45 VAC 45/66Hz, 300 mA maximum

High voltage: 90 - 265 VAC 45/66Hz, 35 mA maximum

6. Connect power.

Wait approximately 45 seconds after power-on before proceeding further.

The following steps require ow in the pipe. Flow signal readings should be taken while holding the ow rate

constant if possible. Otherwise, take the various output readings as quickly as possible.

7. Measure and record

analog or binary outputs.

Current Output:

Scaled Output:

Refer to ow meter wiring diagram for the various outputs available, based on your particular

ow meter model. Use the following formulas to calculate ow rate from measured analog

signals:

GPM = (measured current in mA - 4) X Full Scale Analog Flow Rate

Each contact closure = unit volume identied as “Scale Factor” (measure and record time

interval between contact closures)

8. Compare various output signals

to each other and to the ow

rate displayed and to the control

system.

Compare the ow rates calculated in STEP 7 to the ow rate indicated by the display and the

control system. Refer to troubleshooting guide when readings are inconsistent.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 38 39 40

Comentarios a estos manuales

Sin comentarios

Onicon F-3200 Series Manual de usuario Pagina 32

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos de medición Onicon F-3200 Series