Onicon System-10 P1 Manual de usuario descargar pdf (Pagina 33)

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

System-10-P1 Manual 10/14 - 0656-9 / 18320 Page 33

TABLE OF STANDARD SYSTEM-10-P1 APPLICATION NUMBERS

1983 BTU/HR x 1,000,000 TON-HRS x 10 GAL x 10,000 GPM x 1 DEG F

1982 BTU/HR x 1,000,000 TON-HRS x 100 GAL x 1,000 GPM x 1 DEG F

1981 BTU/HR x 1,000,000 TON-HRS x 100 GAL x 10,000 GPM x 1 DEG F

1980 BTU/HR x 1,000,000 TON-HRS x 100 GAL x 10,000 GPM x 10 DEG F

1979 TONS x 1 BTU x 1,000 GAL x 10 GPM x 1 DEG F

1978 TONS x 1 BTU x 10,000 GAL x 10 GPM x 1 DEG F

1977 TONS x 1 BTU x 10,000 GAL x 100 GPM x 1 DEG F

1976 TONS x 1 BTU x 10,000 GAL x 1,000 GPM x 1 DEG F

1975 TONS x 1 BTU x 100,000 GAL x 100 GPM x 1 DEG F

1974 TONS x 1 BTU x 100,000 GAL x 1,000 GPM x 1 DEG F

1973 TONS x 1 BTU x 100,000 GAL x 10,000 GPM x 1 DEG F

1972 TONS x 1 BTU x 1,000,000 GAL x 1,000 GPM x 1 DEG F

1971 TONS x 1 BTU x 1,000,000 GAL x 10,000 GPM x 1 DEG F

1970 TONS x 1 BTU x 1,000,000 GAL x 10,000 GPM x 10 DEG F

1969 TONS x 1 TON-HRS x 1 GAL x 100 GPM x 1 DEG F

1968 TONS x 1 TON-HRS x 1 GAL x 1,000 GPM x 1 DEG F

1967 TONS x 1 TON-HRS x 10 GAL x 1,000 GPM x 1 DEG F

1966 TONS x 1 TON-HRS x 10 GAL x 10,000 GPM x 1 DEG F

1965 TONS x 1 TON-HRS x 100 GAL x 1,000 GPM x 1 DEG F

1964 TONS x 1 TON-HRS x 100 GAL x 10,000 GPM x 1 DEG F

1963 TONS x 1 TON-HRS x 100 GAL x 10,000 GPM x 10 DEG F

4.6 SYSTEM-10-P1 POINT DATABASE

The Point Database table on the next page lists all of the points used by the System-10-P1 BTU

Meter. NOTE: Also refer to the Siemens’ Application Note, Document No. 140-0280 for more

information.

4.6.1 System-10-P1 Point Database

IMPORTANT NOTE

System-10-P1 BTU Meter totalization registers are 6 digit registers. User dened units and

multipliers are then applied to these values. This is required to allow for the accumulation of totals

over a reasonable time period without exceeding the capacity of the register. P1 variables are limited

in range to 32,767. In order to properly convey the System-10-P1 information, each totalization

0-9,999. The second point represents the digits from 10,000-999,999. The user-selected multiplier is

applied to the units for the rst word. For the second point, the multiplier is adjusted by a factor of

10,000 then applied to the units.

Example: The System-10-P1 would process a Mode 1 Energy Total of 500,100,000 Btu’s, as 500,100

x 1K BTU. The associated P1 variables would be as follows:

• Point 9 – 0100, Units x 1kBtu • Point 10 – 0050, Units x XMBtu

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 66 67

Sin comentarios

Onicon System-10 P1 Manual de usuario Pagina 33